How Often To Clean Barrel For Lead Fouling

Thread Condition:

Not open for further replies.

1. I'm going to start reloading with cast lead 45 acp 200 gr SWC for my Springfield 1911, an XD and a Sig 220.

   Exercise I run a risk hurting myself or these pistols past shooting unjacketed lead?
   Also, How often practice I need to clean these pistols?
   Do I have to end shooting after 200 rounds in one afternoon just to clean the pistol for rubber's sake?

   I don't want to hurt myself, my guns or my friends by doing anything unsafe with reloads. Please articulate this up for me!

2. With a good load you should be able to shoot 4 or 5 hundred rounds in one afternoon easy with no ill effects. A good load will not pb upwardly your barrel. You can shoot lead for the lifetime of the pistol

3. I shoot lead 357's out of pistols without problems simply my 357 levergun volition leadfoul at the last few inches of barrel. I recall the extra xiv" cause the atomic number 82 to heat-up more than a pistol barrel.

4. pb bullets crave a piddling more than of an exact science to come up with an platonic load. Too low-cal and they will function well, simply will lack a little in accuracy, too hot and they will lead the barell, just correct and they will expand to have the rifling fully and tin amaze you. I normally utilise slower powders filling the example more and acheiving the same velocity as jacketed, but usually with lower summit pressure. I utilise bullseye for jacketed HS-6 for lead. You can always use plated bullets similar Rainier makes, they are almost as inexpensive as plainly lead, but a lot more forgiving. I am non certain if the XD has polygonal rifling like glock an HK use, but if this is the case you take to be especially conscientious that there is no lead buildup, as even a pocket-sized amount of barell obstacle tin can increment pressures quite a chip, and a few accept kaboomed when a jacketed roung was fired through a leaded barrel. Just well-nigh any pistols transmission has the "never use reloaded ammunition" but Glock and HK models accept an boosted "apply only jacketed ammunition" alarm.

5. It all depends on your combination of barrel bullets , lube and load. I bandage my own(have been for 37 years) and I don't clean the bores of my hanguns. I shoot .38 spl, .45 acp, .357 magazine and .44 mag. If you are getting no leading in that location is no point in cleaning except to make you experience skilful. Permit your barrel tell you lot what to practice. Bank check it afterward 10-15 rounds, look at it again subsequently 20-30 rds and if there is no or very little leading and information technology does not accumulate I would'nt worry about it in a days outing. Exercise your usual cleaning routine when you go dwelling house. If you are getting leading in the .45 I would change bullet brands till I found i that did not lead. The .45 is a very lead friendly cartridge.

6. Sounds like non enough lube and or not a hard enough alloy for the pressure/velocity. I would say the bullet is running out of lube. Non uncommon with designs for handgun bullets in longer barrels.

7. Almost all of my reloading is with bandage bullets. I do get leading with some loads, especially afterwards a lot of rds fired. No big bargain. five or 6 passes with an old bore brush with some strands from copper Chore Boy pad wrapped effectually it, after a patch with Breakfree usually takes it out. Regardless of load, some guns, because of rougher barrels ordinarily, specially new ones, have a tendency to pb more that others. As far as rubber, using listed loads should exist plenty safety unless you accept a Glock or other make with the aforementioned blazon of rifling.

8. the XD isn't polygonal as far as I remember....
   Thanks for the info!

   I've never shot lead bullets before...what does lead fouling look like? is it easy to see?

9. Yep, it's easy to spot. Yous might want to check your bedchamber later on shooting pb bullets. It's kind of weird but sometimes yous'll get some atomic number 82 blanket in the chamber from when the cartridge is stripped from the magazine and enters the bedchamber. It will rub on the top of the chamber and leave a small scrapping. When the round is fired, the atomic number 82 heats up and creates a thin layer on the height of the chamber.
   I've mentioned this before, since I saw information technology happen on my 1911s. I just used a .38 bore brush to clean the chamber on my hardball gun. You have to shoot FMJs for Leg Matches, but I use a 230 grain RN for practice. In that location were some very minor lead deposits in in that location.

   Navy Vet & SWIFT Boat OIC

10. Depends on how hot...

    you lot load your ammo.........I load for bullseye shooting and after shooting a zillion rounds, have never had to make clean for lead. If you load your rounds fast, they volition lead the barrel. Otherwise, I but cleaned the gun when it got dirty......chris3

11. i'chiliad trying to find the right load to minimize leading. Whatsoever recommendations would be appreciated. I had heard Bullseye was skilful for lead. I similar the Atomic number 82 RNFP rounds.

    thanks

12. I've built 1000s of rounds for a 1911 .45ACP

    shooting a 200 gr LSWC using about 4.8 to five.one gr. of 231 and Winchester primers.

    When our society competition PF for Major was 160, 4.nine gr. of 231 ran about 810 FPS, with extremely low SD and ES--and, from that 1911, virtually ane.5" groups at 25 yards.

    The barrel didn't lead, just I did watch the chamber a bit and kept it make clean. I'm no proficient of powders, only from my experience with pb bullets in .45 ACP, 10 mm, and some in .40S&Westward, you mostly have no issues if you go along your velocities below 1000 FPS.

    As for bullet shape, I really think that's dependent on your firearm--eastward.g., what feeds reliably.

    That's not hard to do with a .45 ACP--and so take at it.

    Jim H.

Thread Status:

Not open up for further replies.

• Domicile
• Forums

  Forums

• Competitions

  Competitions

• Media

  Media

• Resource

  Resources

• Members

  Members

• Menu

Source: https://www.thehighroad.org/index.php?threads%2Fhow-often-to-clean-when-shooting-lead.272741%2F

Posted by: mosescrepare1996.blogspot.com

Share this post